Automatic Sand Blasting Machine-Shot Blasting machine, shot peening machine,sand blast cabinet---MIZHI

Outstanding Advantages

The blasting chamber is made of high quality carbon steel plate;
With a 50W-LED explosion-proof lamp;
With electromagnetic pulse dust removal system;
With a 6mm tungsten carbide spray gun;
With a cyclone separation system;
With a foot switch and a set of filters;
With a set of turntable system;

Contrast Of Sandblasting Products

VS

Before sand blasting

After sand blasting

Working Principle

Sandblasting machine is the category of air conveying machinery. It is in the process of conveying powder particles (diameter 1-4 mm) from one place to another by compressed air in the pipeline and transforming kinetic energy into potential energy, so that high-speed moving sand particles can wash away the surface of the object and improve the surface quality of the object. Before sandblasting operation, the workpiece is sent into the sandblasting chamber, connected with electric and gas devices, and beaten. Turn on the sandblasting lamp, close the main door, hold the sandblasting gun, press the foot switch button, and clean the parts with the sandblasting gun. The sprayed steel shot falls into the pressure tank at the bottom of the sand blasting chamber.

Product Description

1Sand blasting cabinet

1. The blasting chamber is made of steel and welded to ensure sufficient strength.

2. A dust-proof and explosion-proof LED lighting is installed on the top of the blasting chamber.

3. The foot switch determines the start and stop of sand blasting

4. Equipped with a tungsten carbide spray gun and sandblasting tube.

5. Equipped with manual air switch valve, oil water separator and pressure regulating valve.

6. The bottom of the blasting chamber is equipped with a mesh partition. Below the partition is a honeycomb floor, which serves as a storage port for the pellets after blasting.

2 Turntable system

1. The turntable system and the right door are integrated-design. The turntable drive motor and stepper motor are installed inside the trolley, which can automatically enter and exit to achieve automatic loading and unloading process.

2. There is a main turntable on the trolley. The main turntable is made of die steel material and heat-treated whose hardness is greater than 59HRC.

3. The maximum load of the trolley is 100KG, and the maximum installed parts are 1200mm.

4. The outer part of the main body of the trolley is covered with wear-resistant rubber to prevent the steel shot from hitting.

5. The trolley is equipped with a protective cover to prevent the internal drive gear motor being exposed.

6.The trolley and the blasting chamber door are connected. When the trolley enters the blasting chamber, the door is closed.

3Automatic spray gun system

1. When sandblasting, the observation window is used to observe the sand blasting situation.

4Cyclone separator

1. A wind separator system with a full curtain separation system which is good for separation.

2. The rear part of the air separator is equipped with a suction pipe which is used for separating steel shot, sand and dust. The inside has a regulating valve, which can effectively separate the broken steel shots and dust in time.

5Filter dust collectorMDC-12

1.Designed for integration, integrated on the back of the main unit with a filter cartridge inside.

2. Suitable for indoor discharge, dust emission 50mg/m3.

3. With automatic backflushing device,and you can set the backflush interval.

6Electric cabinet

1. Main power two-phase AC: 220V ± 10%, 50Hz ± 2%.

2. The panel is equipped with a pressure adjustment knob, a working pressure gauge, a status indicator, a power switch knob, and the button.

3. Low-voltage electrical appliances: Schneider.

Parameter Introduction

Automatic sand blasting machine parameter sheet + configuration sheet
NO.	Name	Automatic turntable type sand blasting machine
1	Model	MSA-1870-24
2	Air pressure type	Siphon type
3	Working mode	Automatic siphon continuous sand blasting
4	Sandblasting media	Abrasives such as glass sand, ceramic sand, brown corundum, white corundum
5	Application	Surface, such as hardware, electronics, molds, etc., rust removal, degreasing, deburring, descaling, surface removal, and pre-treatment processes commonly used in the coating and electroplating industries to improve the surface of coated (plated) layers. Adhesion.
6	Working size (LWH mm)	150015001400
7	workpiece size (LWH mm)	12001200600
8	Dust Collector	MDC-12 Filter Dust Collector
9	Dust collector fan	4KW 380V/50HZ
10	Light	51W-LED explosion-proof lights (2sets）
11	Gun diameter	8mm
12	Cyclone separator	1pcs
13	Foot switch	1个
14	Solenoid valve	1个
15	Pressure regulating valve	1pcs
16	Pulse valve	1pcs
17	Filter	1set
18	Pressure	5-8KG/m3
19	Blasting glove	1 pair
20	Low-voltage electrical	Chint
21	Power supply voltage	AC220V
22	Total power	5.6KW
23	Total weight	1.56T
24	Oversize size（LWHmm)	460832202644

Industry Application

Shot blasting and derusting production line for Marine engineering machinery parts

Marine Transportation Industry

Shot blasting cleaning line solution for parts of bullet train brake system

MIZHI

Automatic sand blasting machine parameter sheet + configuration sheet